Avda. Pío XII 44,Torre 2-Bajo izda.
Madrid, España
+34 913 459 730
tsi@tsisl.es

Training Schedule

Vibration Analyst Category I (ISO 18436-2) Vibration Institute

curso certificacion analista de vibraciones CAT I

Objectives

Vibration Analyst Category I Certification by training attendees in:

  • Basic knowledges for checking the rotating machinery behaviour using vibration analysis.
  • Basic knowledges about: measurement chain, signal processing, analysis and diagnosis, references standards. Crrective actions and monitoring systems.

Dates

April 4 – 8, 2020

October 26 – 30, 2020

Length

Thrity two (32) hours plus examination

Price

995 €

Vibration Analyst Category II (ISO 18436-2) Vibration Institute

curso certificación analista de vibraciones CAT II

Objectives

Vibration Analyst Category II Certificaction by training attendees in:

  • Reaffirm theoretical and practical knowledges required for the Certification.
  • Deepen signal processing, evaluation and diagnosis of machinery using vibration analysis.
  • Detection and diagnosis of the most common mechanical failures by measurements, analysis and control of vibrations.

Dates

May 18 – 22, 2020

November 16 – 20, 2020

Length

Thrity eight (38) hours plus examination

Price

1.195 €

Vibration Analyst Category III (ISO 18436-2) Vibration Institute

curso certificación analista de vibraciones CAT II

Objectives

Vibration Analyst Category III Certificaction by training attendees in:

  • Advanced knowledge in diagnosis.
  • Qualification to perform, direct and establish monitoring programs of condition in machinery.
  • Qualification to define corrective actions and restrictions of operation machinery.

Dates

May 25 – 29, 2020

November 23 – 27, 2020

Length

Thrity eight (38) hours plus examination

Price

1.395 €

CBM – Condition Based Maintenance – for vessels seminar

Curso CBM en buques. Mantenimiento basado en condicion

Objectives

Operation and Maintenance costs reduction, implementing from scratch and in no more than six (6) months a comprehensive CBM programme or assessing the existing one. The following activities will be carried out:

  • Mentoring and training in how to analyse and identify critical maintenance issues before typical failures occur by means of vibration measurement, analysis and control. Spectrum and vibration analysis training.
  • Definition of the main stages of a CBM Project.
  • Continuous Monitoring/Protection of vessels’ critical equipment.

Dates

March 4 – 6, 2020

September 16 – 18, 2020

Length

Twenty one (21) hours.

Price

990 €

Vibration in diesel engines and in gas turbines seminar

Curso vibraciones en motores y turbinas gas

Objetivos

To specialize in root cause failure analysis of this kind of machinery:

  • Review the operation of reciprocating engines and of gas turbines. Standards and regulation.
  • Introduction to “breakdown consultancy”. Specialization and practice of the main Failure Analysis techniques: critical speeds, run-up tests, modal analysis, etc. Troubleshooting techniques: Dynammic balance in one and two planes, structure reinforcement, etc. Turbocompressors failures.
  • Case studies: Real cases, determination and solutions. Specific cases presented by the attendants. Monitoring/Protection systems maintenance.
  • Complex failures identification ans solution.

Dates

March 18 – 19, 2020

September 9 – 10, 2020

Length

Sixteen (16) hours.

Price

800 €

Noise and vibration on board vessels seminar

Curso vibraciones y ruidos en buques

Objectives

Design and construction of vessels according to the New Specifications and to the environmental directives for reducing vessels´ impact:

  • Review of the current Normative/Standards and Regulaion.
  • Review of the basic conceps of noise and vibration on board vessels.
  • Noise and vibration problems on board vessels identification and solution.
  • Review of the CBM (Condition Based Maintenance) techniques, as an essential methodology for cost reduction.

Dates

March 11 – 13, 2020

September 23 – 25, 2020

Length

Twenty one (21) hours

Precio

1.100 €

Pdm (Predictive Maintenance) and CBM (Condition Based Maintenance) for wind turbines seminar

Curso de MPA y monitorizacion en aerogeneradores

Objectives

To specialize in root cause failure analysis of this kind of facilities (both onshore and offshore installations):

  • Mentoring and training in how to analyse and identify critical maintenance issues before typical wind turbines´ failures occur by means of vibration measurement, analysis and control.
  • To identify the typical failures that can be found on wind turbines and their solution.
  • Definition of the main stages of a PdM project applied to wind farms.
  • Continuous monitoring/protection of wind turbines.

Dates

March 25 – 26, 2020

September 2 – 3, 2020

Dates

Sixteen (16) hours

Price

900 €

Failure diagnosis in pumps seminar

bombas

Objectives

Knowledges and expertise in the failure diagnosis techniques in pumps:

  • Main failures.
  • Applicable Standards.
  • Variable speed test.
  • Modal analysis.
  • Reinforced studies.
  • Torsional analysis.
  • Identification and correction of complex failures.

Dates

June 2 – 4, 2020

October 6 – 8, 2020

Length

Twenty four (24) hours.

Price

1.250 €

Predictive Maintenance (PdM) seminar

Curso de mantenimiento predictivo de averias MPA

Objectives

To Know how to implement, from scratch and in no more than six (6) months, a comprehensive Predictive Maintenance Programme (PdMP) or o assess the existing one. Mentoring and training in how to analyse and identify critical maintenance issues before failures occur by means of vibration measurement, analysis and control. Spectrum and vibration analysis training. To manage all the stages of the PdM project. Introduction to continuous vibration protection/monitoring:

Dates

April 15 – 17, 2020

September 30 – October 2, 2020

Length

Twenty one (21) hours

Price

980 €

Root cause failure analysis seminar: Case studies

Curso especializado averias

 

Objectives

Training and specialization in Root Cause Failure Analysis. Revision of the PdM Basic Concepts. Introduction to “Breakdown Consultancy”.
Specialization and practice of the main Failure Analysis techniques: Run-up tests, Modal Analysis, etc. Troubleshooting Techniques: Dynamic Balance in one and two planes, Structure Reinforcement, etc.
Case Studies: Real cases, Diagnosis and Resolution. Specific cases presented by the attendants.

Dates

April 22 – 23, 2020

October 14 – 16, 2020

Length

Twenty one (21) hours

Price

1.100 €